Elegant, light and delicate scarf tiealmost every handyman can. The secret of this product is that it was created from an unusual yarn, which when transformed into a beautiful lace. When knitting only the extreme loops intersect, and the entire lace part winds in a spiral and turns into a unique product. Knit such a product is a pleasure - because the scarf is beautiful, unusual, you can choose the color of yarn for any taste, and it takes only a few hours to create a masterpiece. The length of the scarf can also be different, but the widththe product is usually small, in a straightened form about 20 cm. Such an unusual scarf consumes the entire skein of openwork yarn. To tie a scarf, prepare:
We begin the process of creating a scarf from the fact thatstraightening yarn. This task is simple, but very important. The thread goes in the package pressed, and when straightened it turns into an unusual mesh. To straighten and untwist it is necessary, of course, not the entire skein, but in stages, that is, approximately 40-50 centimeters. Now take the knitting needles and insert them into every third loop of the first row. That is, we hook the spoke with an extreme loop, then two elements are passed so that they hang freely, then again we pick up the eyelet on the spoke. Then there is a pass of two loops from the grid. We are again picking up. We do this manipulation by typing the loops 5 times, that is, you need to dial five loops on the spoke. It is necessary to make sure thatTo pick up a loop from the second row of openwork yarn, then you can easily get lost and get confused. Therefore, always hold the bottom edge, to spread the grid in full. Now we start knitting.should remain five loops, but they are selected from the grid of yarns not in a row, and again with passes for two stages of the elements. To do this, turn the work over so that the typed loops remain in the left hand, spread the sufficient length of the grid and skip the two elements in the grid. Then with your right hand, take the second spoke, which will be working, thread the edge of the knitting needle into the first loop, grasp the finished loop and hook it on the right knitting needle. In this case, the loop is tied according to the type of the front, and the thread remains behind the work. Again, skip the two grid elements, poke the loop on the left side and grab the new element with the right knitting needle, pulling the newly selected loop again, the loop from the first row (ie from the left knitting needle) simply falls down. Do these pick-ups after every three loops, gradually stitching them into the loops on the left spoke. Then the work is turned over, and the circle is knitloops of dreams by type of facial, that is, the thread should be located on the wrong side of the work. Such a mating will ensure the location of the wide yarn along the spiral turns, which will make it possible to create a three-dimensional volumetric scarf. The main thing when working this yarn does not get confused and do not get off with a simple knitting scheme - do pick-ups every three stages. But with the spinning of yarn, you can lose count, which leads to complete confusion. In the third row, you start the strap from the first loop, which was the last one in the previous row, but before it you pass two loops from the top row of the net of the yarn itself. That is, when knitting this kind of scarf does not work the principle of the extreme loops, that is, when the last loop is knitted by the type of the wrong one, and the first loop is removed. If you work hard, you can see slenderextreme loops, which were tied together. As you can see, each of the extreme loops participated fully in the creation of the series and thanks to such a binding, the edges of the scarf do not bounce, but smoothly spiral from row to row. We knit like this a scarf, the length of which you need. Remember., That this product is often worn doubly folded or makes three turns around the neck, so the length of the scarf should be decent. Each round of knitting is similar to the previous series. In each row, you form the pickups of the loops by the type of facial ones and always tie the side loops in the same way. Be sure to straighten a small area of yarn beforehand so that you do not have confusion when you work. At me on this product the whole skein, face value which is 80 gram is spent. At the same time, the knitted scarf turns out to be quite long, which looks nice when you wear it. The last row has its peculiarities in closing loops. It is not necessary to form the binding of the two loops together and return them to the left spoke. In this work, all five loops are bound at once. To do this, pod all the number of loops on the back of the work, that is, on the basis of purl knitting and pick up a new element from the grid, having receded from the previous pickup three elements, that is, three holes in the yarn. Pull out the overall loop from all five loops, tightening them slightly. Then the next element of the yarn is tied into this loop, finally tightening the edge. That is, you draw two elements in a row. Carefully tighten the end of knitting. As a result, you will have an openwork edge half a century. When you wear the product, other rows will be straightened, the previous round of knitting will merge with the last one and the end of the work will not be contrasting. Our charming scarf is ready. It looks very voluminous and the quality of the yarn is such that the product turns out to be tender and warm. Wear a scarf with pleasure. The white product is harmonious for any clothing. The scarf can be folded twice, thrown around the neck and straightening the place of folding of the product with one hand, pull out the ends on the other side. And it will turn out such a beautiful shape. You can wrap a scarf around a few rounds around your neck,and leave the ends of the product carelessly dangling. Variants of socks of this product are pretty much, connect fantasy and will always look irresistible in things created by yourself.