Charming blouse for your beloved girlto tie one's own hands. Using even an uncomplicated drawing, but picking up delicate colors and unusually soft yarn, you can tie an amazing thing that will be unique, beautiful and soft, which the girl will surely like. About 10 grams of yarn and several evenings of work are spent on such a sweater. A bright appliqué in the form of a multi-character character will add additional colors and mark the front side of the product.
A very important step if you want to link a thing toCrumbs are the right choice of yarn. The thread should not only be of suitable color, but also gentle to the touch, so as not to irritate the skin of the baby and the product of this quality of the yarn is comfortable. Excellent cotton thread, melange, coco, etc. When choosing a skein of yarn, hold it in your hands without squeezing, determine the quality by touch, try not to choose a synthetic compound, the thread of which creaks to the touch. To accurately determine the number of loops for the product, you need to associate a pattern of a pattern of 20 loops, measure its parameters and calculate the loops accordingly. Remove the measurements for a future sweatshirt is not always convenient with the baby, so use the existing product of a similar style and measure its parameters in breadth. The product is knitted in several stages: first, the front and back of the sweater are created, then they are sewed along the shoulder line on both sides, leaving a cutout under the neck, then the hinges from the armhole are typed and the sleeves are sewn from the wrist to the axillary region and immediately the seam continues downwards to the level of the waist. Let's start with the fact that we type a number of loops, according to the calculated number. The first row is tied with a back loop without any pattern. SCHEME
Stages of work
Turn the work to the wrong side and knitaccording to the figure, the face loops, so that the visible side of the front part of the article had a wave from the reverse side at the bottom. The third row, like the first one, is tied entirely with purl loops, so the next even row (fourth) must be created according to the principle of the facial smoothness. Starting with the fifth row, you need to knit a drawingby the attached scheme. Do not forget to remove one loop as an extreme, without tying it. The first three loops are tied as front, that is, press the loop on the left in the direction to the right (parallel to the left nonworking spoke), then toss the loop off the working thread and pull the newly formed loop with the right knitting needle so that the knitting tool takes its position from the right side. The fourth and fifth loop must be tied together, so that one of them forms a single eyelet. Then create a cake, for this you simplythrow the thread on the right knitting needle, and it stays there to serve as a new loop. The next two loops are tied together like facial ones and one new element is formed from them. Next, you need to tie three loops over the face, that is, the facial smoothness. The next element is the creation of a new cap on the right working knitting needle. Then, two eyelets are tied as facial and again a cape is created. Now it is necessary to repeat the pattern drawing the required number of times until the end of the series. Drawing takes 12 loops, so when typing a loop it is better to create a multiple of twelve, otherwise the pattern will have to be divided and correctly bound with the remaining elements. Turn the work over and tie all the loops along the wrong side. To do this, the thread must be held in front of the knitting needles, poking each loop in the usual direction from right to left, hooking the working yarn and pulling the newly formed element onto the right knitting needle, and the loop from the bottom row remains knotted, so it simply falls into the center between two knitting tools. The next row is knit on the front side, like the previous one according to the proposed scheme. All purl even rows are tied with simple backing loops, without adding crochets, etc. According to the drawing, about 10-15 cm of the product is tied, that is, to bring the work just above the waist to the level of the chest. Joining two loops into one and adding a cape allows you to align the number of loops to the original state. Thanks to this pattern of drawing, sharp parts are formed at the bottom of the product, which gives the work an unusual look and the knitted product does not look simple and ordinary. The next part of the backrest and the gear knit on a differenta picture that is called a "rice field". In this binding, one face loop alternates with one purl, that is, knit the first loop (after the extreme) as the front one, and the second one, the third loop again the front one, the fourth one - the back one, etc. When you turn the work over, start knitting not by drawing, but vice versa. That is, where the purl loop is visible, tie it with a face loop, and the front loop with the opposite one. As in the front row, the appearance of the loop was constantly alternating. Then even the even number is tied, too, like the one face, the next purl, and the facial-purl, etc. are repeated again. Spray the front part to the level of the beginning of the neck and divide the loops in half. Further work will be on the two halves (right and left) going separately, because first the 8 loops from the center are closed to one side and the edge is being unfastened, and then it is necessary to return to creating the canvas from the other side. On each next row, tie two loopstogether to form a smooth rounding of the collar zone. The resulting loop is not sewn on the next stage, but is transferred to the "nonworking" spoke. After it is knotted about three centimeters to round the neck, it continues straight knitting to the level of the shoulder. Further, the loops are closed towards the center and it is necessary to proceed to the knitting of the other side of the throat. The back is created in a similar way: the lower part of the pattern with the capes and the union of the two loops into one, and the upper part is sewn according to a simple scheme - the front loop alternates with the purl element. Both halves of the product need to be sewn along the shoulder line, but on one side the seam does not reach the neck, but the buttons are sewn on, and the other edge forms small loops using a hook from the air loops. Measure out the edge of the armhole under the arm and at this pointtype the hinges. Try to knit from a thin yarn to select each edge loop, that is, under it to form a new loop sideways, from which the sleeve will be knit. The principle of knitting the sleeve on the contrary, that is, firstthe most part of the part is tied according to the figure "rice field", it is required to gradually narrow the width of the element. To do this, place the last loops in place in each fourth or sixth row. The cuff of the sleeve is knitted according to the pattern of the pattern, where the openwork napkins are created. The last step is to sew the edges of the sleeve andhalves of the product. To do this, straighten the work on the wrong side, thread the thread into the thick needle and gently seam over the edge, fasten all the parts in the direction from the cuff to the axillary region, and then down to the level of the waist. Children's sweater can be decorated with any appliquewith a fairy-tale or cartoon character. This drawing not only beautifies the product, but also simplifies the task for the mother - finding the front of the product, which is put on the chest. That's ready for a child's gentle sweater from multi-colored yarn, where the main yellow color turns into a rainbow of shades. Such a product will gladly be worn by a baby.