To start creating a dress pattern, you need toto find out for yourself some of the basic nuances that in the literal sense will help in the construction of drawings. Initially, you need to understand what a pattern is and what it is. Pattern - this is the basis, made according to the impression of the proportions of the figure. It is made individually for each woman. With a single pattern made once, you can produce a variety of models, which you can only dream about. For example, changing only one element - the neck, you can get a dress with a deep neckline. To do this, you only need to do it more than on the basic pattern. Pattern-base appears from the drawing. But the drawing does not have to be complex and consist of a huge number of incomprehensible numbers and letters. Everything can be done much easier. The pattern is divided into two halves - it's the back and the front part. In other words, they are called "shelves". One more important parts of the base are the armhole and the dart. A patch is a feature of a hole in the arms. For each bend and the size of this armhole is individual, for any refined taste and needs. But you need to be careful when measuring armholes, it should not be too small. Otherwise, the dress will rest on the armpits. Darts can be on both the back and the front. On the back is a shoulder tuck and waist. Shoulder tuck is made to ensure that the dress does not create a hump on the neck. Talyevaya same darts make the dress stitched, that is, it perfectly fits the figure. Tucks in front help to create the right bend of the chest. They are done on the shoulder. Thanks to them, the breast, as it is necessary, has a bulge. In order for the dart on the shoulder not to be struck heavily in the eyes after the drawing, it can be moved slightly below the axilla. Breast line is a guide for drawingthe most basic pattern. According to her dress tapers at the sides, and on it are the middle Talieva darts. The line of hips is an extension of the chin. The hem extends according to the individual characteristics and desires of each woman. It can be a classic extension of 1.5 cm or more. The most simple pattern of the dress is to create a veryjust. And all this because it is done inside a rectangle. Of course, the most intense moment will be the image of the upper part of the base, where the neck, tucks, armholes and lines for the shoulders. In order to make it easier to draw, the topthe particle can be divided into 3 zones, in which 2 or 3 lines will be located. After this drawing - the top part is absolutely ready. Drawing the drawing will take no more than 20 minutes. Technology of drawing a simple pattern First of all, the measurements are taken:
At the first stage of drawing the most simplepatterns of dresses are drawn a triangle, which measures in height: height from neck to hem; and in width: half the girth of the chest and plus a few additional centimeters. This will depend on the chosen silhouette. Then the rectangle is divided into 3 parts: zone of the back, arm and chest. The width of the back is the size of the back width, divided by two. The width of the arm is half the width of the chest. Breast width is all that remains. In the third stage, the throat line and the shoulder line are drawn on the dorsal side. The line of the throat should lie exactly on the very rectangle, and only the edge of the tip can stick out a little. It is important to note that the width of the throat is 1/3 part of the half of the neck circumference and another 0.5 centimeters are added. And the height of the edge of the throat, protruding above the rectangle - is 1/10 part of the half neck girth and an additional 0.8 centimeters. The shoulder line runs from the edge of the throat and slightlycrosses the boundaries of the back. Its length is the length and 1.6 centimeters for the tuck. At the fourth stage on the line of the chest in place of the armhole, the back and transfer armholes are drawn. The armhole line goes down to the chest line. The chest line is measured from the height of the armhole to the edge of the shoulder. The level of the breast line is the size of the armhole. The line of the backhoe arm is always from the edge of the shoulder and bends in the armpit. The trail of the armhole moves away from the bend of the armhole at the top to the bend of the armhole in the armpits. And one more point is added - axillary. By connecting three points, the transmission line is obtained. Next is the image of the chest zone. This is the line of the throat, the line of the front shoulder and the dart on the chest. The top part of the simplest pattern of dress is ready. Next, the pattern of the back and the transmission are divided into the right side and the left side. It's easy! The seventh stage is the waist and hips. The waistline is measured from the top of the pattern and down. Line of hips - from the waist down. In the penultimate stage, the bends of the side of the transmission and the back are drawn, and the front tucks of the waist and back are added. Lateral bends 1 dimension in two sides from the line in the middle. Next, darts are drawn at the waist of the back and transmitted. At the final stage there is an extension on the hips. To do this, you need to find the difference from half the girth of the hips and half the girth of the chest. This number is divided by 2, that is, as much as you need to extend the hem of the simplest pattern of the dress. And now every fashionista can put on a dress from her fantasies. Masters are advised not to be afraid of their new ideas and experiment on their images.