Blind souvenir with roses for Valentine's Day with your own hands with a description and a photo.

December 12, 2017 handmadebase

For those who prefer to give interestingpresents made with our own hands, we offer a lesson on modeling in the mixed technique of the panel "Heart with roses". It will also be useful for educators, teachers, junior schoolchildren and their parents. Our master class will contribute to the development of imagination, thinking, fine motor skills, accuracy and artistic-aesthetic taste. Thanks to the creation of hand-made articles, the child can awaken a genuine interest in studying nature and transfer the acquired knowledge to artistic images. Joint production of the panel will make it fun and interesting to spend leisure time with your baby. Before you start, it's not superfluous to repeat the rules when using PVA glue:

if possible, use a brush;
Glue should be taken exactly as much as required for a certain stage;
glue is applied in a small and even layer;
he should not fall on other objects or on your body;
Having finished work with glue, it is necessary to close it tightly and remove it;
Working surface and hands are washed with soap.

To create the sawdust dough is necessary:

sawdust of small size;
glue;
sunflower oil;
little starch.

In addition, to create a craft, you can not do without:

sandpaper;
varnish of three colors (green, pink and red);
brushes; scissors;
glue PVA;
gouache;
a cocktail tube;
glue "Titan";
satin ribbon;
self-hardening plasticine;
stack; toothpicks;
molda;
mold-sheet;
clerical knife.

Course of work. We prepare the dough from sawdust. Take two glasses of sawdust, half a glass of starch, half a cup of water, three tablespoons of PVA, one teaspoon of sunflower oil. Sieve through a sieve sawdust. Glue is soluble in water. Thoroughly mix the sawdust with starch and gradually pour in water with glue. Continuously stirring, add oil. The dough should look similar to a sand dough. Using food wrap, wrap the board. The dough is covered with a film and rolled into a thickness of 10-15 mm. Take the knife and cut it into a heart shaped form. Using a smoothie, make holes. Take a brush moistened with a water-adhesive solution, and smooth the outskirts of the heart. Dry and peel using sandpaper. Open it with lacquer. Let's proceed to modeling flowers. The panel will be decorated with pink and red roses. A toothpick sticks into the clay. Using red plasticine, roll 5 balls5 mm in diameter. Slightly it having rolled from one side, we make a drop. Then we dress her on a toothpick. It will act as the core of the rose, where we will glue the petals. Again, roll a ball 50 mm in diameter. Put it in the center of your palm and flatten it with your finger. With the help of the thumb and forefinger, we form petals, of medium thickness. One flower of such petals will need a dozen, and if they are more dazzled, then this flower will become even more magnificent. In the first row there will be two petals. Take the harness and wrap it with one petal in such a way that a beautiful cone has turned out. Do not try to glue the petals tightlywidth, enough to wrap and hold, then it will stick itself. Opposite the first petal is the second. In the second row there will be one more petal. The first of them is glued in half, leaving the second edge as it is. This is done in order to bring the edge of the final lobe underneath. It is located from the first row higher by 0.01-0.02 cm. Three lobes are applied in accordance with the illustration. The third row will consist of five petals. They should also be glued above the previous petals. Remember that the edge of the final lobe is placed under the edge of the 1st petal. In other words, the petals are placed not against each other, but in a spiral. Continue wrapping the petals. At the output you should get something like this: Dry. The lower part of the rose must be flat, so that it fixes securely on the panel. To this end, with the help of a stationery knife, we align the edges of the rose (this stage of work should be performed only by an adult). The half-opened rose is molded similarly from the five petals. For modeling the bud, the base and two petals are taken. Using a green plasticine we make 3 balls-sepals. Then they are glued to the bud of the rose. We take plasticine of the same color and roll the sausage of small thickness, then it is rolled out and 5 triangles are cut using scissors. The triangle is attached to the sepals. Now, using green plasticine, roll 7thin sausages, the length of which is 10 mm. The resulting stems are glued to the bud and the half-opened rose. Take the nail scissors and make small incisions on the stem. So we will create our spikes roses. In total, red plasticine we need to model five opened roses, one half-opened and one bud. The same scheme will be used for modelingthree opened roses and three half-opened ones and one pink plasticine bud. Modeling leaves. First it should be made for the leaves of the mold. Take a tin can or a plastic bottle and cut a strip of 50 x 40 mm. The ends of the stripes are held together by means of an adhesive tape. Alternatively, you can use the ready-made boat. Of green self-hardening plasticine, previously thinly rolled up, leaf-shaped cut out seven leaves. For manufacturing on foliage of streaks a special adaptation is used - mold. If there is no such, use the stack. Dry it. Glue fix the red roses on the base. Then the bud and the half-opened rose are glued. Adhesive is fixed on the basis of a rose of the same color. Next, glued half-opened roses and bud. Red leaves are glued to the leaves. After that, the foliage is stuck to the roses of the same color. A satin ribbon is inserted into the previously made hole. Carefully inspect the craft, and if nothing is missed, then it is finished! We hope that the proposed master class will rally even more of your family, when you spend together fun and entertaining time, making souvenirs with your own hands.

Comments

comments

Comments

Related posts: