Bantams on September 1 of the white ribbons with their own hands for girls. Step-by-step instruction with description and photo

January 25, 2018 handmadebase

School bows are one of the brightest attributesfor September 1. But their own hands can create unusual, large, festive, unlike the others. Bows on the rubber can decorate and tails, and braid. This master class describes the process of interesting school bows that will suit any school holiday. To create bows you will need:

The tape is 3 cm wide, it should be unusual withembossed pattern, for example, with squares, flowers, curls, etc. Still, the braid should be dense in texture. The length of such tape for one product is about 75 cm.

A usual satin ribbon, 2.5-3 cm wide, per one bow is spent a little more than half a meter.

Border width 2-2.5 with an unusual texture, always transparent. In this work, a dense capron beika with a silver stitch was used.

Thin ribbons of white color for making a bow on the side. The texture of the beiki should be different: organza and satin.

Transparent glue, that is, special rods andA special pistol that allows them to be heated and turned into a sticky mass. Such glue is very convenient when working with matter, because it instantly dries, does not smell and does not stain a thin satin.

Midpoints for bows that will decorate the work and make school accessories more vivid.

Rhinestones - a few pieces.

Anchorages with which the bows are fixed on the hair. These can be bows or gum.

Burner or scissors with a cigarette lighter.

Charming hair jewelry for September 1are created in several stages: first you need to make a foundation, then curls, the next step is the creation of the main central bows. Another time is spent on the production of small elements in the form of curls, which adorn only one side and give the product a share of coquetry. At the final stage, all the details are glued together, and the last chic - rhinestones is added. For the base, prepare cuts of 15 cm. Two parts are created from a simple satin ribbon, and the third element is needed from a dense tape with an unusual texture and pattern. With the scorch or scissors, cut the endsblanks, so that the two cutting lines from the edge converge 1 cm at an acute angle. If you use scissors, then you must scorch the cut lines near the flame of the lighter. In no case do not you bring a strongly gentle satin very close to the fire, it can be smeared, and then there will be black marks. Satin details are glued together. Fixation occurs strictly in the center in the figure of the letter "X", and the third element is located strictly in the middle and will determine the horizontal center of the product. When making the second bow, in creating the base, you can not break the fixing angle, so overlay the parts over the first joints. Let's start working on the curls. These details provide the product with splendor, volume. For curled elements we use a dense beautiful ribbon. It takes two cuts of 30 cm for each product. Place the tape face to the table and glue each edge to the middle of the cut, but so that a curved circle is formed. The second part, glue in the same way. Both parts are glued together so that one part is a mirror image of the other. The glue is applied to the very edge of the central part of one part and the other half is immediately fixed. For a central bow, prepare a pair of cuts of 24 cm. They are cut from a simple satin ribbon, 2.5 cm wide. Each piece of tape is glued along the cutting line into the ring. Try to fix the edge of the tape no more than 1-2 mm, otherwise the product then does not take the form of a batik. The place of gluing the edges in the second stage is fixed to the opposite side of the ring, to make the most simple bow. It will take a couple of such details. Both blanks are glued together in an ikas and you get a pretty bow that will decorate the central part of the product. From the last braid, which is transparent,need cuts of 20 cm. From the details, glue similar bows and join them into a four-pointed bow, but the angle of the joint should be the same as the previous part. On the satin part, glue a bow from the nylon. Be sure to observe the symmetry, so that the work is smooth and accurate. Bows paste in the curls, but the ends of the details should look the same. Bonded bows must be attached to the base of the product with a hot glue. Now we are starting to create a minimalized bow, which will decorate one of the curls of the product. First, from the transparent tape, glue the element in the form of a bow with hanging lower ends. From a thin satin ribbon, glue a pair of parts according to the principle of the number eight. Both parts are connected by glue in the center, and then fix on the first element of the transparent organza. Decorate with such a bow a single convex part and add a rhinestone to the center of the small bow. On the other curls, too, attach the rhinestones, and decorate the middle with a more massive element. Turn over the bows and glue either rubber bands or clips so that the product can be easily fixed on both the spit and the tail. Clamps will allow to decorate even the dissolved hair. Charming school gum (or clamps) are ready to decorate the hair of the student on September 1. Such accessories, created with their own hands, will be useful for any solemn school event.

Comments

comments

Comments

Related posts: