A lesson on making a flower in Kansas technique for beginners

Beautiful things are not always difficult inmanufacturing. Even an aspiring needlewoman of a very young age, who has the desire to create beauty, can make pretty ornaments in the form of flowers, identical in form to river water lilies. Kanzash flowers can be worn on elastic bands or hairpins, they will decorate the hair on weekdays, and on holidays. Light flowers look gentle on the hair of blondes, and in brunettes they play in contrast and create an accent in the whole image. The size of the flowers can vary, these decorations are 7 cm in diameter and look great on the schoolgirl's tails.

Video guide

Materials and tools

Each leaf of a water lily flower has a characteristicThe shape of the petal with a triangle at the end, and the inflorescence consists of several layers. To create such a petal does not require much effort and skill, but it is necessary to stock up the following material:

Stages of work

First, you need to create large bottom elements from4 cm ribbons, the upper petals are made in a similar way, but it is always easier to learn how to make new parts on larger sizes. Take a cut from the gray ribbon (or other color) at 10, the width of which is 4 cm. Fold this flap in the center at an angle so that the product takes the form of a right angle, more precisely the ends of the cut must be combined at 90 degrees. Again, bend the part so that that part of the element,which is bent to the right side, fell down to the first edge. Both sides of the cut must turn out to be a satin side up and a part with a sharp end in the center is obtained. To give details of the petals of the lily, stillit will be necessary to create longitudinal veins. You can create such bends with a couple of creases at the bottom of the element. Each bend should be of a minimum size and move from the center to the side. So the bend on the right and left side form a wave from the center to the edge, so they are like mirrors between themselves. Save the newly formed part shapewill allow soldering with a hot burner (or soldering iron). To do this, attach the piece to a surface that does not melt (for example - glass), press the bottom of the part with a ruler and burner, draw a line. The cut should be 1-2 mm of the base, at this point the two ends of the tape are welded together and the element will take the final shape. Take the rounded part for the base of the flower. In this example, the petals are glued exactly to such a round part and do not cling to each other, but they must be placed as tightly as possible. Approximately seven of the same elements of steel color create the first tier of the product. These petals are the largest, the rest of the details will fill the work center magnificently. From the tape is more thin, that is, the width of which -2.5 cm, it is necessary to create similar petals. Each piece of white satin should have a length of 9 cm. Bend the cut in the center, only the fold line is formed in an oblique direction, and spreads the ends of the tape in different directions. Then bring the edge of the tape, which is sideways, to the lower part, completely aligning with the first end of the cut. It is very important that the atlas "look" upward in both sections. The lower edge of the part gets streaked thanks totwo uniform folds. To solder the base, you need to press the parts and cut off 1-2 mm soldering iron, or you can clamp the base with tweezers and burn the edge of the part with a flame from the lighter. Obtain the received parts between the elements of gray color, that is, the second layer hides the lumens of the first layer of petals. Then, the attachment points of the elements are shifteda little in the center, so the third circle of white details is formed. The last circle of white blanks is glued to the very center so that one edge of the detail lies on the edge of the previous petal and the petals tightly close the middle of the product. Stamens are stuck in the central part of the flower. At the last stage we start to decorate the flower, that is, bright crystals are fixed in the center of the lower petals. On each element is enough for one rhinestone. Turn the water lily and glue it to it.clip or elastic, you can use a small hair clip, crab. Such a beautiful flower will be able to create by hand the craftsman without experience, since the excesses in these petals are quite simple. Ornaments created with their own hands are doubly more pleasant to wear, since each element preserves the memory of your hands. Lush flowers will decorate any hairstyle!

Comments

comments

Related posts:

A lesson on making hair clips in the form of a flower in Kansas technique with rhinestones How to make a vase for a flower using origami technique. The lesson is free. Guide to the manufacture of fluffy white rim in Kansas technique The lesson of creating a poodle with the help of quilling techniques for beginners - a master class Kanzashi: lotus-shaped barrette, kanzashi for beginner ideas and master classes