We prepare our child for any season. Beautiful patterns of comfortable children's trousers for every skillful mother. Simple instructions and photos

We prepare our child for any season. Beautiful patterns of comfortable children's trousers for every skillful mother. Simple instructions and photos

Children grow quickly enough, therefore, eachMom will come in handy to master the sewing technique, in order to save money on clothes for the right needs. Below is a pattern of trousers for preschool children. From this pattern you can also sew shorts, overalls. Pants will be an indispensable clothing in the wardrobe! The first thing you need to do is take the measurements. Measure your child, and write down all the parameters on a separate sheet. Now proceed directly to the structure of the pattern of children's trousers. The presented pattern can be used for tailoring products, both girls and boys. To properly build a drawing, you need to remove such measurements:

  • The length of the trousers is 60 centimeters. Measure on your side, from the waist line and to the very bottom of the future product.
  • The length of the product to the knee is 34 centimeters. Measure simultaneously with the measurement of the length of the trousers. From the waist line and to the middle of the knee.
  • Half-girdle of the waist is 27 centimeters. Measurements are made on the narrowest area at the waist. Write half the value.
  • Half-girth of hips - 32 centimeters. Measurements are carried out at the maximum protruding points of the buttocks. Write half the value.

photo-scheme for the pattern. Photo №1 We now proceed to the very structure of the pattern. The front half of the trousers. On the prepared sheet of paper, in the upper corner on the left, draw a right angle, at which the vertex is the point A. The length of the product. From point A we measure the length of the trousers, and denote by point B. In the example, it turned out to be 60 centimeters, but each lays its parameters. The length of the product to the knee. From A to the lower region we measure the length of future clothing to the knee. Denote the end of the segment by the point K. By the example, it turned out 34 centimeters, but you postpone your values. From A, K and H to the right side we lay horizontal straight lines of any length. Waistline. From the point A on the right side we measure half the parameter of the half-hip of the thighs, add to the resulting value of 1 centimeter and call the end of the point A1. Step line. From the point A in the lower region we measure half the parameter of the half-hip of the thighs, add to the resulting value of 2 centimeters and call the end of the point C. From C to the right side measure the interval that is equal to the segment AA1, and call the end point C1. A1 and C1 are connected. Thigh line. The distance is divided into three halves. We call the lower point of partition B. From B to the right side we measure the segment that intersects A1C1. We denote the intersection point by D1. The top point of the partition is called B. It must be used for the side seam line. The line of the bow. From point C1 to the right side we measure the segment equal to one-tenth of the parameter of the half-grip of the thighs, and denote by C2. The angle at the vertex C1 is divided into two parts, by bisectrix we measure 1.5-2 centimeters, and we call the end of the line 1.5. From C1 to the top, we lay 4 centimeters and denote 4. Points 4; 1.5; C2 smoothly connect. The bowline will pass through A1; B1; 4; 1.5; C2. Bend line. The CC2 line is divided into two equal halves, and through the point of separation parallel to the AN draw a fold line. The intersection with the waistline is called A2, with the knee line - K1, with the bottom line - H1. The width of the future clothing along the line of the knee. From K to the right side measure 2.5 centimeters, and denote the point K2. From K1 to the right side we measure the segment, which is equal to the line K1K2 and call k3. Width of the product at the bottom. From H1 to the right and left region we measure the segment equal to K1K2, and denote by the points H2 and H3. Line of side cut. B together with K2 connect, and the resulting segment is divided into two parts. In the right field we measure half a centimeter. From A to the right side measure 1 centimeter, and call the end of the line by the number 1, and then connect it with B; B; 0.5; K2; H2. The line 1 and K2 are connected by a smooth line. K2 and H2 are a straight line segment. Thus, the line of the side cut of the product was obtained. Step line. C2 and K3 are connected by a straight line. The resulting segment is divided into two halves, and put it into the left half a centimeter. The step cut is made out. C2; 0.5; K3 is connected by a smooth line, and K3; H3 - straight line. The front half of the product is the bottom line. From H1 to the upper region we measure half a centimeter. H2; 0.5 and H3 are smoothly connected. Dart on the waist line. From A2 to the lower region we measure 6-8 centimeters, and the end of the line is called the figure 8. The value of the groove of the front part dash is equal to two centimeters. From A2 to the right area and to the left we measure one centimeter. Points connect these with the number 8. photo-scheme for the pattern. Photo # 2 Back of the product. The back part of the product is built according to the diagrams of the front part. It can even be built on one sheet of paper, and at the end, just copy each half. Seat line. The segment A2A1 is divided into two parts. The point of the section is called the figure 3. From C1 to the top, we post a straight line through 3, continuing it even beyond the waist line (about 3 centimeters) and denote A3. The point of intersection with the BB1 ​​line is B2. From B2 to the top, we lay 2.5-3 centimeters and call the letter B3. From C2 to the right area we measure 4 centimeters, and we call C3. From C3 to the lower region, we lay one centimeter, and we call C4. For a bisector with a vertex C1 we measure 2-2.5 centimeters. The seating line is created by smooth lines through points A3; B3; 2; C2; C4. Waistline. A1A extend to the left to any length. With a circular we make a mark from A3, the radius which is equal to half of the waist's half-compass and add another 3 centimeters. We call A4. Width along the knee line. From K2 H2 to the left side we measure 1 centimeter. From K3 to the right area, we also measure 1 centimeter. Correspondingly we call the points K4 and K5. Width along the bottom line. From H2 to the left side we measure 1 centimeter. From H3 to the right area, also measure 1 centimeter. Accordingly, we call the points H4 and H5. Line of lateral seam. A4 connect with K4. From B; B; and C draw horizontal lines in the left region up to the intersection with the segment A4K4 and call B1; B4 and C5. The segment C5K4 is divided into two equal parts and from the point of division into the right region we lay off 0.5 centimeters. From A4 to the right side we measure 1 centimeter, we call the end 1. We connect 1; IN 1; B4; 0.5; K4; H4. The section from 1 to K4 is drawn with a smooth line, and the section from K4 to H4 is a straight line. Step line. Points C4 and K5 connect, divide the segment into two equal parts. From the point of division into the left side, measure 0.7-1 centimeter at a right angle. Points C4; 1; K5 smoothly connect. K5 and H5 are connected by a straight line. Decoration of the lower part of the trousers. From H1 we put 0,5 centimeters in the bottom part. Draw the bottom line of the back of the product. We connect points H4; 0.5; H5. Dart on the waist line. The segment A4A3 is divided into two halves and at a right angle from the point of division to the lower region we draw a perpendicular 8-10 centimeters. Ditch solution 2 centimeters. From the place of division in the right and left side, we postpone one centimeter and connect the points with the top of the dart. The work is finished. Now you have a base on which you can sew excellent classic trousers for your beloved child. The base is suitable for both boys and girls. Variants in width and length may differ from examples. Pockets can be made in their own way. The trousers can be sewn with a pajama version, only the side and step cuts make straight lines without bends. photo-scheme for the pattern. Picture №3 You can sew a pajamas version, millet make outlateral and stepwise slices by lines without absence of deflections. Sew an elastic band, expand the bottom of the product, do not tug around the waist. By such patterns you can sew shorts, breeches, overalls, you only need to make some changes to the patterns. photo-scheme for the pattern. Photo №4 Before you begin to cut the product, you should check the pattern for all parameters. And forget about the allowances on the seams!

Comments

comments