Knitting a gray bolero "Vivienne" crochet according to the pattern and detailed description

December 5, 2017 handmadebase

Original bolero "Vivienne",crocheted according to the pattern Bolero is an important part of a woman's wardrobe. Putting it on over a festive dress will give your image a certain romance and femininity. And if the need arises, you can easily take it off. Today we will offer you a master class on knitting a bolero. For this you will need Drops Merino extra fine yarn, consisting of one hundred percent wool (250 grams for size 44/46), and a hook measuring four millimeters. The density of our knitting: knitted seventeen CCHs in ten rows are equal to a part of the product measuring ten by ten centimeters. We knit a patternMake increases Create 2 dc through the nextCCH on all sides. Replace the 1st CCH of each row with three VP (air loops), the row must be completed with one CCH, knitted through the 3rd VP of the beginning of the previous row.Knitting the back We create seventy-five airloops, turn the product and do it this way: knit one sc (single crochet) through the 2nd VP from the base of the hook. Next, knit one sc in the next three VP. Next comes the repeating part: skip 1 VP, create 1 sc, knitting in the next six VP. In this way, you should repeat until the end of the row. As a result, you get sixty-five single crochets (the 1st VP is equal to one sc). After this, we continue knitting, adhering to the pattern A 1. We start with the row marked with an arrow: a - through the initial four loops, b - up to the final five loops, then - c. As a result, you will get an eight-time repeating pattern in each row.Then we repeat the next four rows of the pattern untilthe required size. Please note that after making four centimeters vertically, you need to add one DC on all sides. Duplicate such additions every three centimeters of the product. After four centimeters, you only need to add one DC. Continue knitting the pattern up to twenty centimeters vertically. At the end, do not cut the thread, but move on to knitting the edge. Knitting the edge We begin knitting by creating a SC on the upper part of the back of the product, evenly distributing seventy-one SC. Then freely make thirty-six VP (armhole). Then knit one SC through all the SC at the bottom of the back of the bolero, evenly passing eight SC (fifty-seven SC). Next, freely knit thirty-six VP (armhole), fasten with one connecting loop through the 1st SC at the top of the back (two hundred loops). Cut the thread and then knit, starting from the middle of the upper part of the base of the back. Row 1: Make 1 slip stitch through the middle sc, then do the following: (repeat part) three ch, skip one loop, then knit one sc through the next loop. Repeat this pattern along the entire edge. Finish the row with three ch and one slip stitch knitted at the beginning of the row (this makes 100 arcs in this row). Row 2: Make one slip stitch and one sc through the 1st arc, then do the following: (repeat part) three air loops, one sc through the next arc. Repeat this pattern along the entire edge. Finish the row with one slip stitch knitted in the 1st sc. Then do as shown in the diagram for the second row until the product acquires a vertical length of five centimeters.Row #3:Make one slip stitch and one sc through the 1st arc, then do it like this: (repeating part) four air loops, one sc through the next arc. Next, three VP, one sc in the next arc. Repeat this pattern until the end of the row. Finish the row with one slip stitch, knitted in the 1st sc. Then do as shown in the diagram for the third row until the product acquires a vertical length of nine centimeters. Row No. 4: Make one slip stitch and one sc through the 1st arc, then do it like this: (repeating part) four air loops, one sc through the next arc. Repeat this pattern until the end of the row. Finish the row with one slip stitch, knitted in the 1st sc. Then we do as it is written in the diagram for the fourth row until the product acquires a vertical length of twelve centimeters. Row No. 5: we make one connecting loop and one sc through the 1st arc, then we do it like this: (repeating part) five air loops, one sc through the next arc. Then four ch, one sc in the next arc. We repeat this pattern until the end of the row. We finish the row with one connecting loop, knitted in the 1st sc. Then we do as it is written in the diagram for the fifth row until the product acquires a vertical length of fifteen centimeters.Row #6:make one connecting loop to the center of the 1st arch (which consists of five VP) (diagram A 2, the row is marked with an arrow), then make six VP, one SC through the same arch. Then knit as follows: (repeating part) knit three DC through the arch of four air loops, one DC, then three VP, then - one DC through the next arch of five VP. Repeat this pattern until the end of the row. Finish the row with three DC, knitted in the final arch of four VP and one connecting loop, knitted in the 3rd VP from the initial part of the row. Starting from this row and until the end, do as follows: create three connecting loops four DC in the 1st arch (which consists of three VP). Then knit as follows: (repeating part) one air loop, one SC through the middle DC (three DC of the previous row). Next, one VP, five dc into the next arc consisting of three VP. Repeat this pattern until the end of the row. Finish the row with one VP, one dc through, knitted into the middle sc (the final three dc from the previous row), then - one VP and one connecting loop, knitted through the 3rd VP from the beginning of the row.Final row:(repeating part) three air loops, one sc through the 1st VP. Next, skip the 1st dc, make one sc through the next dc, then - three VP, two dc through the 1st VP, skip one dc, make one sc in the next dc, then - three VP. After that, knit one dc through the 1st VP, skip one dc, make one sc in the next VP, then skip one dc, make one sc in the next VP. Repeat this pattern until the end of the row. Finish the row with one connecting loop, knitted in the 1st VP from the beginning of the row. Cut the thread with scissors. The width of the edge is twenty centimeters.We process the armholes We process the armholes like thisway: in the back part we make one connecting loop through the 1st dc. Then we knit in this way: (repeating part): three air loops, one sc through the next dc. In the front part of the product: we make three VP, skip one loop, one sc in the next loop. We repeat this pattern until the end of the row. We finish the row with three VP, one connecting loop, knitted through the 1st connecting loop from the beginning of the row. That's it! The product is ready!

Comments

comments

Comments

Related posts: