We learn how to make a hairpin from tapes with our own hands - a detailed master class from a professional
A delicate composition of satin ribbons can decorateclip or hair clip. Such an original flower in pink and white is perfect for a small baby or a blonde girl. Amazingly, they create by their own hands petals from ribbons in Kansas technique, which merge into a single floral composition. To create an ornament in a pink palette, prepare:
Decoration is created in several stages - firstit is necessary to create a flower, and then large petals of a thin ribbon for the top of the composition, the rest of the area is filled with round petals, which we will do in the third stage. For the petals of the main flower, you will need square blanks with sides of 4 cm. Cut them out of a bright and pale satin, each color of 10 pieces. It is necessary to create a double lobe, a core,which will be like the rounded petals of Kansas, and the outer layer is a sharp petal. For the inner layer, take a light pink workpiece and fold it over the oblique. The sharp angles of the satin element are brought to the bottom, where the right angle is. Bend the edges back, bending the part strictly along the center line, and fix in this position. For the outer layer, take a bright workpiece. At the first stage, it bends similarly along the oblique, turning into the shape of a triangle. Noting visually the middle of the part, bend it again, so that the fabric is evenly formed into 4 layers. A bright pink workpiece is superimposed around the light. The details must be arranged so that the acute angle of the outer layer remains on the same line of the rounded part of the inner lobe. Press the ruler of the base of the petal so that all eight layers of fabric are fixed. Using a burner, cut off 2-3 mm from the base, welding all the layers in a single seam. Then, using the ruler, the lower part of the double lobe is leveled. Cautious movement with the burner cuts the bottom folds. If the bottom seam is correct and even, the petal is freely positioned in an upright position. It takes 10 identical elements. On a round flap with a diameter of about 1.5 cm, glue 8 double petals. The middle of the flower should be decorated with another element. To hide the traces of glue and add effektnosti. We proceed to the second stage on which thelong tubular petals. Long they will need cuts of 12 cm from thin tape. Just make three blanks, for one you can use a different shade. Each element is folded in the center across,while the smooth satin side remains outside. The burner will need to cut off part of the part along the line from the outer corner to the opposite side, retreating 3-4 mm from the edge. Burner fuse this seam very carefully, since tubular petals often diverge at the place of adhesion. Turn the petal through the place where the cut line does not reach the corner of the part. As the basis of the whole decoration,an oval piece of pink ribbon, its size is 4 cm in width, and in length is slightly larger than the clamp you have chosen. At one end of the center, glue the first tubular flower, decorate it with rhinestones. The second and third petals are pasted near the central element, at an angle to each other. Decorate the middle of the details with rhinestones. Glue on a rhinestone is more convenient to put a toothpick. On the opposite edge of the oval base with the help of glue fixed the main eight final flower. The remaining space is filled with doubleround lobes, their number is difficult to predict in advance, since the size of the pins can be different. To create a white-pink petal, prepare squares of 5 by 5 cm from a white satin, and from the pink ribbon you will need square blanks of 4 cm. Bend the large element diagonally and smooth out the inflection with your fingers. From the pink detail, too, form a two-layered triangle. The blanks are superimposed on each other (smaller by greater), between the fold lines there is a gap of no more than 1 mm. The edges of the parts lead to the bottom, forming a diamond. Bend the details, bending it along the center line. A warmed-up burner cuts the bottomthe petal. To create a smooth seam and solder many layers of the atlas, the movement of the hand with the tool should be clear, fast and with pressure on the tool. The second hand should fix the work with a tightly pressed ruler. Press the seam on the back of the part and drip some hot melt into the resulting hole, then squeeze the petal. Create several smooth, neat rounded petals. First, the petals are pasted into the gaps of the petals of the main flower, but only on one side. Then the second, third and subsequent rows are formed from the rounded elements, depending on the size of the base. The remaining two sharp double petals are pasted on the sides of the flower to smooth out the transition from narrow to wide. Turn the work over and glue the clamp along the longitudinal line in the center of the base. After 5 minutes all the glue will dry completely and the decoration will be ready. This barrette looks both gentle and chic. Wear it with pleasure!