Master-class on creating flowers from satin ribbons in Kansas technique
Charming flowers that will decorate the dress orhairstyle, you can create from a simple material - satin ribbons. Handmade flowers will be useful for girls and girls on a festive day, they easily cling to the hair, attach to the rim or they can decorate the belt. Snow-white flowers will add tenderness and romance to the image of any lady. Flowers can be created on the basis of petals, thenaccessories will be more voluminous, magnificent. The color of the base can be any, for example, green to match the natural leaves. In this version, the gray flower base fits the tone of the selected dress. For work you will need:
For a base, cuts of 16 cm are required. Cut them from the ribbon in any color. In this craft, the leaves of the base and the petals of the flower are created using the same technique, but because of the difference in width and length, the elements look different. Large petals are formed as follows: find the middle of the cut (to do this, first bend the tape, connecting its ends), tighten the middle with your finger and bend the product at an angle of 45 degrees, but strictly in the center. Now mark the middle of the inflection and from this pointbend the workpiece again, so that the front side of the atlas lies on one side and a double lobe is formed. The top of the part will have a triangular point like some garden flowers. Such a flat form does not occur in nature,because the petals must have bends, veins, so you need to refine the details. To give a more original volumetric shape to the petal will help bend at its base. First, make a crease on one side, having absorbed a part of the base, from the other side, too, creates a similar wave. Both bends must "look" at each other and be symmetrical. Create four large identical elementsfor the foundation of a single product. On the rounded blank of diameters of 3 cm, paste these four details in the form of the letter "X", so that you get a semblance of a bow. From the white ribbon you need to cut the billets 8 cm in length. Each element must be bent in the central place at an angle of 45 degrees. In this case, one end of the ribbon will be turned to us with a satin side, and the other with a wrong side. Now bring the edge that is bent to the side,to the bottom of the part. With this manipulation, the part is bent at the top in the middle of the previous crease and the ends of the ribbons lie with the satin side up. At the base of the formed part,Bends, by which the middle of the petal will go a little deeper and take a more natural form. To do this, simply bend the right side of the base of the element with the wave and, similarly, bend the left side of the petal. Create several identical snow-white elements from a thin ribbon. The number of parts for a single flower varies between 15020 pieces. The next step is to start assemblingflower. Take the prepared base with large details in the form of petals and fix the small elements in the center of work with liquid hot glue. Each petal is glued close to the previous one, so that there is no gap between them. Petals are glued in three tiers, if the firstlayer is an arbitrary ring with pressed petals, the second level is created at the place of the joints of the lower row. The petals of the second tier also form a circle, but slightly smaller in diameter. Since the elements move slightly to the center. The third tier is created from 4-5 petals, which are very tightly pressed both on the edges and in the center, so that there is no lumen left, and the flower seemed lush, full, stacked. Finished middles fiddle in half so that theyacquired the appearance of stamens inflorescence. If you do not have such details, you will need cuts of fishing line for 5-6 cm, the edges of each part dipped in hot glue and immediately plant a small bead or large beads. By sticking the lines along each end of the bead, you will have a beautiful imitation of the flower center. Place the folds of the stamens abundantly moistened with glue and immediately press to the middle of the flower. The petals of the third layer are raised and fixed to the stamens, for this they need to be pressed tightly upwards. On the back of the workpiece are attached hair clips orelastic. With a suitable outfit, this flower can decorate the bezel (fix it preferably on hot melt). If you are going to decorate a dress with such colors, then just sew them with threads to the intended place. A charming flower is ready to decorate the hair or outfit of a little princess or an adult girl. Rhinestones, glued to the lower petals, will bring brightness and originality to the product.