Master-class weaving from rubber bands will teach how to make your own hands of rubber bands shoes for dolls - slippers.
We are all used to the fact that clothes and shoes for dollssew or knit, but you can also weave it from ordinary latex rubber bands! This lesson is no less fascinating and interesting. In addition, it takes a little time. It's best to weave shoes, so we'll make slippers for the chrysalis. To weave such slippers we will need:
- Rubber bands;
To begin with, we form a chain of 12 loops whiteelastic bands. You can take any color you like. If you want the slippers to be larger, then we need a longer chain. You can simply apply a chain to the leg of the doll and watch how much more you need to gum the gum. For marking we will put a clip on the 3rd loop from the top. And we will enter into it a hook. This will be the beginning of the series. If there are no clips, then you can use rubber bands of any other color. Draw through it 1 rubber, the 2nd part we throw on the hook. Now the first elastic band is dragged through all the elastic bands. We do not tighten the knot too much. So we flog until the end, looping each hook in turn. You need to weave the last loop twice. So we'll tug round until the sole gets the right size. Each time through the last loop of the tail, 2 times. We change clothes when we weave through the marked petticoat. Now we will weave the slippers, sowe use red color. Or any other that you like. But in this row we will not tie through the loop, but through the transverse rubber bands. They are located on the side of the hinges. And the next red series plaid through the loops asusually. Such ryadochkov plaid 3 - 4. This depends on the desired height of the slipper. Now we count out 12 loops on both sides and mark the loops with an elastic band of a different color. If your slippers are larger, then count down so that on both sides there were the same number of loops. These gums should be exactly the oppositefriend. You can fold the slippers in half and so will be better seen. We return to the beginning of the series and plait in the usual way with red rubber bands up to the 1st mark. Here, from the marked loop to the 2-nd marked loops we sew with a decrease. That is not in the loop, but in 2. We hook into the inner part 1 of the loop (half-loop) and immediately into the inner part of the 2nd loop. And only now we sew 1 elastic band. We like, like 1 elastic band, connect 2 half loops. After the 2-nd mark again, the tattoo without any deductions. So we sew another row. Now define the place under the strap. We pass a rubber band through the loop 1 and form a chain of 10 rubber bands twisted twice. For beauty, you can alternate rubber bands in color. We dial the chain until it becomes the desired length. Now let's make a flower to decorate the slippers. For this you need to take the machine. The weaving will be performed in 2 rows, so the bottom row needs to be removed. We pull the rubber bands on the 3 pins of the upper row, turning them with an octagon. The same is done on the bottom row. Then we will stretch 2 gum on all 6 pins. Now crochet we will skin 2 lower elastic bands in the center of the weaving. Then we put on all 6 pins 1 pinkRubber and discarded on the 1st lower elastic band. We throw on 6 pins one more pink elastic band and just drop the lower ones. So we throw another 4 times pink gum. Then 2 times we will put green gum in the same way. As a result, 2 green rubber bands will remain on each pin. We reset the bottom. Now we transfer the rubber bands from the 1st pin of the upper row to the 2nd, from the 3rd pin to the 3rd column of the bottom row, from the 2nd to the 1st pin of the upper row. We drop on the 1st rubber band from below. Now we put the hook in the center of the flower and stretch it out2 white gum, but fix the 2 nd part of them below. You can put them on a hook or a stick and press it against the machine. Now we have 2 white gums on the hook, we gradually remove all the bands from the pins on the hook. We pull out the weaving without removing the hook that holds the white gum. We squeeze the white gum through all the elastic bands on the hook. Form the nodule and tighten it. We remove the additional hook. Attach the flower to the strap in the usual way. You can also decorate slippers with a button or bow. Here are such funny slippers for dolls are obtained!