The master class will teach you how to make your own hands a New Year tree from sisal

Of course, in our homes for the New Yearthe long-awaited guest will always appear - the Christmas tree! How are we without it? After all, in order to give gifts to each other, we need it. Otherwise, where do we put our gifts? But even if you do not have a place for the most beautiful and vibrant Christmas tree, or you do not have the opportunity to purchase it, do not despair. In that case, I decided to offer you an excellent way out! And let's do it yourself, with our own hands, create a beautiful and magical Christmas tree! All the necessary material for the work I indicate in the list below:

• Plastic pot,
• New Year's wide ribbon,
• The cone is foam plastic,
• Sisal green,
• Sisal white,
• Silver garland in the form of snowflakes,
• New Year's silver ball,
• Floral wire,
• Glue gun,
• Rods for gun glue,
• Alabaster,
• Water,
• Snowflake,
• A bouquet with a sprig of Christmas tree and a gift,
• Beads are white,
• Paint green acrylic,
• Brush or sponge.

Well, all the necessary material is prepared. Let's move on to work. To do this, let's first take a floral wire in the form of a stick. We bend it halfway. We insert this wire into the very center of the top of the foam plastic blank. Green paint paint our workpiece, so that through the sisal it was not visible. And created the effect of a full tree of sisal. We take the green sisal. We divide it into ribbons, as if tamping with our hands, forming a uniform texture. And, fixing the sisal with hot, hot glue, glue it around in a circle on the workpiece. Thus, we will glue all the stock with you sisal green. Then, as we stick our hands, we press the sisal clockwise. Then smoothly continue to twist also the attached wire. Our task is to fix the sisal on the wire without a lumen, making it the continuation of the crown. That's how it will look like. Then we still need to close the bottom of the cone with the sisal. To do this, we will form a flat circle with a diameter equal to the bottom of the workpiece. And glue the workpiece with glue. Using a sharp knife, make a hole in the middle of the bottom of the workpiece, pasted with sisal. As you may have guessed, we will insert the trunk from the branch into this hole. Then drip a small amount of hot melt inside the hole and on the very tip of the branch and immediately insert it inside the billet. Very little time and the stick stuck tightly. Now, carefully gluing, we draw a garland around the axis of the entire tree, as seen in the photo. The tip of our Christmas tree, which we have made offloristic wire bend beautifully in the direction of the wave. But in general it can be bent as you want! So, most importantly, on the tip we will glue the same hot glue a small ball of the same silver color as the garland. Decorative snowflake glued on the side of the Christmas tree, closer to the bottom. At this place we will attach our decor - a decoration for the Christmas tree. Over snowflakes we will glue any beautiful New Year's twig, in my case these are leaves with a flower, a gift and a sprig of spruce. Now let's proceed, so to speak, to the landing of ourChristmas trees in a pot (in the ground). In order for the tree to be well fixed, we need to "plant" it in a pot forever. So, fill the alabaster with a plastic pot. Add the water there and begin to mix thoroughlyall the content. When the mass is uniform, directly to the center we send the second side of the tree trunk. We fix the tree in one position right on the center for about a day, maybe a little less. When the tree will stand firm and do not swing, you can safely continue the work further. Again, apply to hot melt. We take white sisal and white beads. We tear off a small strip of white or beige sisal. And with his help we will decorate the pot. With the help of hot melt glue on the sisal circle to the trunk, pot and frozen mass. And when almost everything is ready, we will add very little - decorate our tree with white beads. Also glue a pair of white beads and a white sisal. Take the tape and form a bow from it. Glue this bow on the side of the pot with a Christmas tree. And now our tree is ready! It is so beautifully decorated! And how did you like it?

Comments

comments

Related posts:

The master class will teach you how to make your own hands a New Year's toy on a Christmas tree - a coffee star. This detailed master class will teach you how to make your own hands a fir-tree Master class with photo and description will teach you how to make your own hands a Christmas ball on the tree This master class will teach you how to make your own hands a New Year greeting card. The master class will teach you how to make your own hands a New Year's craft - a snowman from glasses