Weaving bracelets from rubber bands came to us fromAmerica and has already conquered the hearts of needlewomen not only in our country, but all over the world. All the charm of this kind of needlework lies in the availability of materials and the simplicity of the technique of execution. Each girl and girl dreams of a variety of beautiful bracelets in their boxes, so weaving from rubber bands is one, though from the youngest, but already quite popular types of jewelry making. In this master class we will weave a simple, but very elegant bracelet "Chess".
Materials and tools
- Rubbers pink and blue colors;
Stages of work
We will brace the bracelet with two forks. Apply one fork to the other outer part. That is, the teeth of the forks must be directed away from each other. Then pull the black rubber band on the upper fork. Pull it off, twist the figure eight and pull the second side onto the lower fork. Next, we will wear one pair of rubber bandsteeth of both forks. To make the drawing we had in the form of chess, we will alternate the colors of the rubber bands. We will put on one rubbery pink color on the very first tooth on the right on the top fork. Upper we will call that fork, which is closer to us. Pull the other side of this rubber band onto the same prong of the opposite fork. Next, go in order and pull the pink rubber on the second tooth and extend it to the second tooth of the lower fork. With the next two prongs we do the same, but we use blue rubber bands. Now take the hook and hook it to the lowest black rubber band on the top fork. We spend it over all the teeth and let go in the center, that is, between the forks. We turn the forks and from the bottom also remove the blackrubber. Next, pull the black rubber on all four prongs of one fork. Stretch so that the side of the rubber, which is located between the forks, was higher than the one that is located outside. We pay attention, that that side of the rubber, which is on the outside, should lie below all the rubber bands on the fork. Next, we put rubber bands one by one on the pairs of teeth of both forks, as in the last time. We have not changed the colors yet. That is, first two pink, then two blue. We pull one black rubber band on all four prongs of the second fork in the same way as last time. This rubber should also be the lowest. Now we drop the crochet into the center one at a timerubber bands with each tooth. We will take off one of the lowest colored rubber bands. Black, which we have below all, until we touch. So, we take off one loop from each tooth of both forks. Next, we throw in a new layer of rubber bands. We throw, as well as the previous ones, on four pairs of teeth of both forks. But now we change the color of the rubber bands. Now first one pair of blue rubber bands, and then one pair of pink ones. Now we take off the lower black rubber band, which is worn on all four prongs. It is necessary to throw off that rubber, which is the lowest of the two black ones. And so in every row. And again we remove one of the lowest color loop from each tooth on both forks. On that fork, which was left without a black rubber, pull one black rubber on all four denticles. Apply a new layer. The color of the gum does not change. Two blue and two pink. Further, according to the already known algorithm. All the subsequent series are repeated, only the colors of the gums change. Two layers begin with a pink pair, and the next two - with a blue. So we need to weave until the braceletwill not be ready. Periodically apply it to your hand and see how many more layers you need to weave. When the bracelet reaches the desired length, we will have to remove it from the forks and fasten it with a clip. At the end of the weaving will need to remove the loop in this way: first two lower colored stitches. It turns out that on one fork we will have one color loop on each tooth and that's it. And on the other fork will be one black rubber band on all four denticles and one more color on each tooth. Now we are tattooing the last row and here we will not put on the black rubber band. Just put on colored rubber as usual. Remove the last black rubber band in the center and remove the lower rubber bands from each tooth. Now, on each fork, there are four colored rubber bands. We collect them on one tooth of one plug and the second fork. We hook in all four eyelets on onefork, take a black rubber band and stretch it through all these eyelets. One end of the black rubber band is on the hook, and the other on the finger. We pull the black rubber from the finger to the denticle, on which are the last four loops. We hold the black rubber band, and we shoot the color ones in the center. Black rubber we pull on the hook and we catch the clip for both its ends. Further on the other end of the bracelet we find a black rubber band and we catch the clip on it. That's such a cute bracelet!