The original design of the pattern of an air beach dress. A beautiful outfit for a beautiful woman. Photos and instructions

January 17, 2018 handmadebase

Beach dresses are the hit of the summer.Below are 5 different models of beach dresses. They are simple and do not require any special education or cutting and sewing skills. There is nothing complicated in sewing the presented models. First, you will need to draw a rectangle, preferably even, and outline the figure. Any woman can handle this task. However, some points should be discussed in advance to avoid difficulties. You can draw the elements of the future dress directly on a piece of fabric with chalk or soap. If you can’t draw it right away, then make a pattern out of paper, and then outline the details on the fabric. All the models that will be created are symmetrical. In other words, the right and left halves are mirror images of each other. To get everything right, the pattern piece should be folded in half. Check if the edges of the halves match. Some tailors use a little trick: they draw the right half on the fabric with chalk, then fold the material in half, clap their palms on the fabric, and the outline of the left half is transferred to the material itself.Make seam allowances with a reserve of 3-4centimeters. You can always cut off the excess, and if there is not enough material, then you will have to do everything again. The material should shrink a little after washing. Therefore, it is better to wash a piece of material in advance, and only then start cutting. You do not have a sewing machine? Do not worry, any studio or clothing repair shop can stitch the seams. Just go in and ask the dressmakers to make a few seams. It will not cost much. Beginners should know the term "drawstring", because it will constantly appear in the article. Drawstring is an empty space that is left for pulling in the elastic. Now you can start sewing the first model of the dress. First, draw a rectangle, the width and length of which depend on your preferences. Think about how you would like the dress to be (long or not very), wide or not. The front half and the back are the same!Sew the side seams.We design the upper part of the front and back in the form of a drawstring, a ribbon for ties on the shoulder will be pulled into it. Do you want a fitted version of this model? Then take stretch material, and the dress will fit perfectly. However, if you are not sewing from stretch, then the side seams should not be designed in a straight line, but curved at the waist. And then, you should also sew a small invisible zipper into the side seam. An elegant dress is ready! Let's start sewing the next model. The most important thing is to choose the right fabric for sewing the presented model. The material should be thin, airy and flowing. Only from such fabric can you easily create soft folds.Underwear knitwear has such properties,jersey, satin, silk, muslin, crepe varieties, etc. Today, there are many mixed fabrics, so always touch the material before buying. If the fabric "flows" beautifully and flows in smooth folds, then this is the ideal fabric. Everything is clear further, looking at the picture. The length of the rectangular figure is 2-3 meters. Everything depends on your parameters and on how you see the folds. The height of the product depends only on your preferences. The dress will have only one seam on the back. In the central part, it is necessary to make a cut with scissors about 5-10 centimeters. This will be the depth of the neckline. We design the upper part of the material in the form of a drawstring, into which we tighten 2 ribbons. The ends of the ribbons should be sewn into the seam located on the back. In the front, the ribbons come out of the drawstring into the central slit. When putting on the dress, the ribbons will simply be tied around the neck. We tie the dress with a belt under the chest. The second model of the original dress is ready! Let's start sewing the third version of the dress. We choose the fabric using the same method that was used in the second model.If the matter does not flow, then you will getinstead of beautiful flowing folds, a trapezoidal sarafan, which is unlikely to please anyone. This model is even easier to sew than the previous two. Take a T-shirt of your size, trace it on a sheet of unnecessary wallpaper. Draw the future product around the outline. Do not worry if the right side is slightly different from the left. First, draw, and then make the right and left sides symmetrical. Another important factor: if you have a large bust or are pregnant, then the front hem of the dress should be made longer. Otherwise, it will ride up in front - and it will not be beautiful. Try on the dress, and see that the hem is the same both in the front and in the back. Correct the errors, cut off the excess. After the details have been drawn, cut out, basted by hand side seams and shoulders, try on the dress. If everything is to your liking, then stitch the product on the machine. So, we drew, cut out, swept the side and shoulder seams by hand, measured and, if everything is to your liking, stitched them on the machine. The beach sundress is almost ready. All that remains is to process the neckline and armholes. You can fold the edges inward and process them with a stitch. Or you can make the armholes and neckline with bias tape. The third version of the beach sundress is ready! So, model 4. We cut out a rectangle from the fabric, which, if you figure it out, consists of two squares. In other words, the length of the rectangle should be 2 times greater than its width. Now you should find the middle in the rectangle, and draw a straight line that separates the squares of the front and back. As a result, you get the shoulder line of the future beach product. On this line we will create the neckline. In the diagram, it is shown as a narrow rectangle, but, of course, this is not necessary. You can, in the end, just make a small cut along the shoulder line with scissors.First, you need to mark a segment on the linefuture cut and while sewing make sure that it is placed strictly in the center. We try on the dress and at the same time correct all the shortcomings. Manually baste the side seams. Try on the dress again. If everything is fine, then stitch all the seams on the machine. Now you need to process the neckline, armholes and the bottom of the dress. If you sewed from a non-crumbling fabric, and the cut of which does not run in arrows, then the edges of the product can not be processed. The presented dress model is made of T-shirt knitwear. By the way, various beautiful patterns on the dress can be ordered from companies that print pictures. You can choose a pattern from a company or find your own graphics on the Internet, upload it to a disk and bring it to the center so that the image can be transferred to the dress. Now we move on to the final stage - we sew the fifth model.As you can see, the principle remains the same, onlyThere are already sleeves and a V-neck. Draw the sleeves in the form of a trapezoid, however, you can depict them as rectangles. The buttons play an exclusively decorative function. You are the creator of the dress, so you can choose the type of neck, sleeve shape, trim elements, and so on. Or you can create a drawstring under the chest in the center of the front square or gather the material with an elastic band sewn on from the inside.

Comments

comments

Comments

Related posts: