We remember the school. Classical pattern of school dress for our young student. Photos and instructions

January 24, 2018 handmadebase

School dresses are a separate storyUSSR. In those days, all girls were required to wear a uniform to school, which they usually sewed themselves, because it was much cheaper. Today, all school graduates always wear school dresses with white aprons for the last bell. Materials for sewing. The fabric called "Pikachu" (100% polyester) 3.5 m with a width of 1.5 m is ideal. There was another fabric option, gabardine, but it is denser and not very pleasant to the touch and to the body. Try to find a lightweight fabric, since May can be especially hot. Pay all your attention to this issue, because it depends only on you whether your daughter will be comfortable and convenient in a dress for the last bell. All the sewing instructions below are given for a girl who wears size 44. First, you should check the finished patterns.

If the shoulders have coincided, then you can mark the fold line. The collar stand must coincide on the neck.

It is necessary to immediately check the neck circumference, because ifIf you don't do this, the dress may be uncomfortable to wear. For example, a girl's waist size is 37 centimeters. If you divide this value by 2, you get 18.5 centimeters. On the pattern - 21 centimeters. As a result, everything will be free in the neck area, and most importantly, nothing will press and there will be no feeling of discomfort.

Check the length of the gear and the backrest.

Now you need to determine the length of the future skirt.To do this, you can attach the pattern to the right side, and put the apron pattern on the left. The apron is 43 centimeters long, so the skirt should be a little longer. If the girl does not like to wear short clothes, then the dress can be lengthened. The optimal length is 50 centimeters. Now you need to correctly construct the sleeve length. Consider a model of a dress with a short sleeve (approximate length 25 centimeters). At this stage, you should take measurements of the arm circumference and compare it with the pattern along the short sleeve line. For example, the girl's arm circumference is 26 centimeters, and on the pattern it is 33 centimeters. This means that the sleeve will be loose. You can put additional marks on the shelf so that everything matches perfectly when sewing. And only after that, you can cut the shelf, since there will be a relief line here.Now let's move on to constructing the collar.If you want the collar to always be buttoned, then you don’t need to change anything on the front pattern. If you want there to be a top button that can be unbuttoned, then draw a facing on the front. If you decide to make a stand-up collar, then you will also need a facing. Advice. The facing can be drawn on the back. Let’s start cutting. Don’t forget to make seam allowances, so put the necessary marks in advance, lengthen the skirt to the required length. Make a hem allowance along the bottom of the sleeve. In order to sew the skirt, you will need to cut out two pieces the entire width of the fabric. You can make a pleated skirt. The bottom of the sleeve and collar should be glued with interlining.Now we move on to sewing the product itself from the cut out parts.

Align the markings on the chest, the relief sections of the front, the shoulder sections, as well as the side sections.

Now you should do the first fitting of the product. On the shelf it is necessary to pinch the child with spines, and then on the back we choose the place where the tucks will best be placed. At 44 size they will not have to be touched at all. Everything will have to be done strictly, as in a pattern. For smaller sizes, they will need to be moved closer to the center.

Overlay the bottom of the sleeve, as well as the cut of the bottom. Relief sections are sewn, in the middle of the transfer is ironed. Finish the stitch along the stitching seam.

Shoulders are cut off, and we take into accountmodel collar. If the gate is on the counter, then the hindquarters are stuck in the shoulder. If the collar is standing-turn-down, then the bottom is not sharpened. The shoulder seam should be pressed from the side of the backrest.

The tags of the sleeves and armholes are combined, we embroider the sleeves with a tentative seam.

It's time for the second fitting! It may happen that the length of the shoulder of the product will be greater than the length of the shoulder of the model itself. Therefore, everything needs to be corrected. It can happen that the shoulders will be greatly omitted, so you should sew the shoulder pads. Then there will not be any wrinkles in the area. We sew up our sleeves. The seam is pressurized.

We sew the collar. If you chose a gate on the rack, then just process it and vtachayte. If you chose to stand-off, then let the girl try on the product, and tell the sensations. In the neck area should not be cramped. It will be better if you lower the line of the neck in the middle on the front by 1 centimeter. The collar is crocheted with the seam allowance. On the sides it is necessary to sew, and then to turn out in such a way that the neat corner turns out. Fold the finished gate in half. The angles must coincide.

Advice.You can cut off the entire allowance that you made when cutting along the neckline, and you can cut off much more along the front. You can also rip open half the shoulder and free the facing, since when sewing the collar on the stand, the facing was stitched into the shoulder. We combine the marks along the neckline: the middle of the collar with the middle of the back, and we combine the mark of the middle of the front part with the edge of the collar. We sew in the collar according to the following options: we sew in at the same time; first we sew in one, and then the other. We check the corners so that everything is even and matches. Special notches should be made along the neckline. In order for everything to be neat on the wrong side, you can process the neckline and facing in two ways:

The seam stitching the collar is overridden, and afterwards we sew the bottom to the shoulder.
The neckline of the backrest is processed at the same time with the podbortom.

Let's get to work on assembling the skirt.The darts on the back should be ironed closer to the middle. Then, distribute the folds evenly and stitch the back of the skirt. On the shelf, align the strip and pin it with needles. Put a mark on the middle of the strip, and then push off from this notch, distributing the folds on the front half of the skirt. How to make folds correctly?

In places where the folds will be placed, special marks must be made.

We combine the inconsistencies.

The fold line now requires a good ironing.

Similarly, iron the second crease.

Each fold should be turned up and ironed.

Overlay the edges of the skirt, and bend.

On the reverse side, the folds can be secured with interlining, and the edges with cobweb.

Now on the skirt there are neat creases.

When the folds are already evenly distributed,it is necessary to stitch the side seam. We bend the bottom of the sleeves to the required length and stitch. We bend the bottom of the skirt to the required length and also stitch. We sew on buttons, having previously made loops. We decorate the dress with cuffs and a collar. A white lace apron will add a special effect.The dress for my beloved daughter-graduate is ready! Now it should be ironed well and can be worn for the last bell.

Comments

comments

Comments

Related posts: