Step-by-step description of the performance of the blue dragon from paper

January 9, 2018 handmadebase

A small dragon is performed quite simply. It is only necessary to tolerate and adapt a little, then you will succeed.

To perform our dragon, you will need a sheetblue paper in the form of a square. The square should be folded on the diagonals, and then immediately deployed. Then you need to bend it in half, turn it 90 degrees and bend it in half a second time. Completely unfold your blue square and you will see the main 4 lines that turned out at the fold.

Origami lovers who are looking for a dragon scheme are welcome. This article will deal with step-by-step instructions for the execution of such a mysterious character as a dragon.

Place the square in front of you so that any of the main lines look at you. To the lower half of it you need to adjust the sides of the other diagonal.

Then you need to close these folds of the top half of the diagonal. There should be a small square.

Origami lovers who are looking for a dragon scheme are welcome. In this article, a step-by-step instruction for the execution of such a mysterious character as a dragon will be dealt with. Photo # 3

Bend the lateral corners to the line in the center. The location of our square should not change.

Origami lovers who are looking for a dragon scheme are welcome. In this article, you will understand the step-by-step instruction for the execution of such a mysterious character as a dragon .. Photo # 4

The upper corner must be bent so that youA triangle with equal hips emerged. Field of this, expand our artwork back to the square of item 3. It formed 3 new lines, which are an inscribed triangle with equal hips. The square should be placed so that the top of this triangle looks at you, and its base is located on top.

The lower corner of your square needs to be raised. Note that manipulations should only be performed on the top layer. The line of our fold must necessarily coincide with the base of the resulting triangle.

With such manipulations, the side corners must turn around and lie down along a line that runs through the center. On the front side should be a diamond, while on the wrong side there is a square.

Turn your creature and with similar manipulations point up the bottom corner, you should get a diamond.

Then the corner that is at the top of yourThe rhombus must be lowered to the lower one. Turn over your artwork and perform a similar operation again. Should be a quadrangle, which will have two sides shorter and two - longer.

Next, you need to bend the upper corner of your quad to the point where the lines cross the fold and immediately bring it back. Turn your hand-crafted thing in the opposite direction and do the same.

Expand the paper structure as in the illustration. Should come out the same table on the big legs.

Then add up your design, check with the illustration. The "worktop" must be concave inwards.

Before you should appear a pentagon with a single sharp angle, which should look directly at you.

You need to carefully fold the corners, located on top.

Raise up the corner, located down on the front side.

You again see a diamond in front of you. And that the diamond came out and on the second side, you need to deploy the work and also bend up the lower corner.

Holding the right corner, you need to turn the "page", the position of the diamond should not change. Then do the same operation from the wrong side.

A new rhombus will appear, in which the lower corner will be solid, and the upper one will be cut into two parts.

After you need to bend the bottom corner to the top, unfold your craft and do the same operation.

Before you should be formed isosceles triangle.

Now we'll work with the face layer. The lateral part must be bent to the base and immediately returned to its original location. Perform the same operation with the other side.

New lines should be formed, along which it is necessary to bend the "hare's ear", a cut must be formed at the bottom.

"Ear" to bend in the right side. You need to deploy your work the other way and make a similar ear, but you need to bend it to the left.

Then you should raise your work, holding it in your left hand for the resulting ears. Flip the page with your free hand to open a triangle, the hips of which are equal.

It is necessary to take up the upper corner of the layer located at the top, and point downwards.

Fold the resulting figure again in half and then you will have a tail.

Grasp the corner of the "tail", locatedbelow (you do not need to disclose the figure), and unfold its upper part. The lower corner needs to be lifted up until the tail looks right (see photo). Your work should already be on the surface of the table.

"Hare ears" should be sent to the right side. The same operation should be performed with the left tail. Open your triangle, point down the top corner, then fold the tail twice and also lift it up until it completely looks to the left.

The preparation of your dragon should be placed oncountertop and bend the "tail" on the left in half, it will be thinner in half. First engage the front side, then you need to bend and the wrong "tail". Exterior halves while you need to invest the way you see in the photo.

A similar operation should be done with the right tail.

After that, the "ears" should be bent, they should be located perpendicular to the "tails". Now they can be called wings. Paws need to be bent, as in the photo.

"Tail", which was on the side of the bent paws - this is the neck of our dragon. But first you need to bend our "tail" up, while pushing it inside.

Look at the illustration, the neck of your dragon should look the same.

Part of the neck needs to be bent. It will become the head of our dragon.

Part that is designed for the head, you needbend again. Should be two unequal length halves. The neck to the neck will be the shorter part, and the long one - the nose of our dragon. The nose needs to be folded so that it looks like a tuft.